33. The plasmid vector most commonly used to introduce genes into plant cells is:
(A) the CoEl plasmid
(B) the Ti plasmid
(C) the R1 plasmid
(D) the Ri plasmid
(E) Plasmid pUC19

29. In _____ reproductive isolation develops and new species arise without geographic separation. (A) Adaptive radiation (B) Adaptive speciation (C) Allopatric speciation (D) Sympatric speciation (E) Tempo of speciation

30. Which of the following enzymes may be used to detect single nucleotide mutation? (A) DNase I (B) DNA ligase (C) Exonuclease (D) Integrase (E) Restriction enzyme

31. For a population to be in Hardy-Weinberg equilibrium, it must satisfy the following conditions except: (A) The population is very large. (B) Mating is random and all individuals are equal in reproductive success. (C) Lack of gene flow. (D) Mutations do not alter the gene pool. (E) None of the above.

32. Which of the following plays an essential role in sex determination of Drosophila melanogaster? (A) Alternative spicing (B) cis splicing (C) RNA editing (D) Self splicing (E) trans splicing

34. The phenomenon that more than one phenotypic characteristic are controlled by a single gene is known as: (A) Polyploid (B) Polychaete (C) Pleiotropy (D) Polygenic (E) Polymorphism

35. Which of the following about meiosis is NOT true? (A) Meiosis is preceded by the replication of chromosomes. (B) Crossing over occurs in Prophase I, which typically occupies most of the time required for meiotic cell division. (C) At Metaphase I, the chromosome tetrads are aligned on the metaphase plate. (D) The sister chromatids making each doubled chromosomes separate at Anaphase I. (E) In Telophase I, the chromosomes arrive at the poles of the cell, followed by cytokinesis. 

1901 下列敘述何者為非？(A)設計圖為設計單位為表達設計理念之圖，而將其作為招標文件並訂為工程契約時即稱建築執照圖 (B)施工大樣圖為廠商依據設計 圖之規定，配合現場實際狀況及其他配合條件所繪製之圖樣 (C)工作圖為廠商分項工程施工時，對臨時性工程施工順序、機具材料搬運、放置場所之說明所須使用之圖樣　(D)CSD圖為設計階段界面整合重要措施，係作為SEM圖之製作依據，並作為日後施工階段各分標廠商繪製施工圖之依據。

1902 下列何者不屬於工程界面管理所採用之措施？(A) CSD(Combined Service Drawing) (B) SEM(Structural , Electrical and Mechanical) (C) CIP(Coordinate Installation Program)　(D) Shop Drawings。

1903 下列何者不屬於施工階段之品質管理措施(A)環保與安全衛生計畫 (B)自主檢查表 (C)設備功能測試運轉與檢測程序與標準 (D)建立並執行工程界面管理。

1904 下列敘述何者為非(A)整體施工計畫書之最佳研訂時間，為決標後至工程開工前提送核可 (B)結構工程相關之分項施工計畫書，應於開工前送審完成 (C) 泥作、門窗及裝修工程之分項施工計畫，應於結構體完成後施工前送審完成　(D)景觀工程之分項施工計畫，應於施工前提送審核。